Photo of a box of StaticWorx CoatZF static-dissipative floor finish. The box is brown with a white label on it with some product information and a picture of an installed ESD epoxy floor. The product information reads: 'Static-dissipative floor finish. Designed for high traffic areas. Easy to apply. Long-lasting static protection. Can be applied over conductive tile and ESD coatings without diminishing electrical performance. Note: Not for use over regular (non-ESD) flooring materials.'

CoatZF Static-dissipative Floor Finish

✔ Static dissipative

✔ Low tribocharging

✔ Zinc free

✔ Low VOCs

Select an option to add this to your cart.

$330.00 USD /
Subscription -

For orders exceeding 150 lbs and/or for bulk or resale orders, please call 617-923-2000

  1. While StaticWorx CoatZF is intended primarily for use on ESD floors, it will contribute temporary static-dissipative properties to non-ESD floors. When used on non-ESD floors, the floor must be tested regularly, as well as after each application, to ensure and confirm electrical performance.
  2. Some extra high traffic areas may require an initial 3-coat application.
  3. This Item is non-returnable/non-refundable.
  4. Coverage rates may vary. Variables outside our control can affect the end result: condition of the floor; equipment in use; procedural deviations; skill of the applicator, and other possible factors. See below for coverage details.
  • 2,000 sq. ft. per gallon, per coat on tile/epoxy (minimum two coats required) – effective coverage 900-1,000 sq. ft. per gallon.
  • <2,000 sq. ft. per gallon, per coat on concrete (minimum two coats required) – effective coverage <900-1,000 sq. ft. per gallon.

StaticWorx CoatZF floor finish is a hard, impenetrable finish, designed for use in high-traffic areas. Unlike most ESD waxes and finishes, CoatZF static-dissipative floor finish can be applied to conductive tile and ESD coatings, such as StaticWorx GroundWorx Basics epoxy, and replenished without diminishing the electrical performance of the ESD flooring surface.  

Comprised of 18% solids, application is easy and improves productivity. Fast, easy-to-use Coat ZF provides a clean, hospital-like shine. CoatZF can be applied by the regular cleaning crew and requires no more work than would be required with routine waxing and buffing.

CoatZF is specially formulated for application in computer rooms, electronic assembly rooms, telephone sub-stations, or any area where static control is desired. Cross-linked polymer chemical structure prevents leaching or wash-out of static-dissipative properties and provides long-lasting static protection.

While StaticWorx CoatZF is intended primarily for use on ESD floors, it will contribute temporary static-dissipative properties to non-ESD floors. When used on non-ESD floors, the floor must be tested regularly, as well as after each application, to ensure and confirm electrical performance.

Can be applied to: Concrete, Epoxy coatings, Polyurethane Sealers, VCT, SVT, SDT, Any ESD tile

Standard coverage: 900-1,000 sq. ft. per gallon (with double application)

Directions

Best results are obtained when StaticWorx CoatZF is applied to surfaces which are 60°F or warmer with relative humidity between 40-65%.

  1. Remove old finish or wax with StaticWorx EcoScrub Degreaser (stripper). Follow directions on stripper label for application.
  2. On initial application, for optimum appearance apply three to five coats of finish. No more than 3 coats should be applied in an 8 hour period
  3. Apply thin, even coats, allowing the finish to dry between coats. Depending on humidity and temperature, dry for 30 – 45 minutes before applying the next coat.

 

Budget-friendly Easy 5-Step Static Killer Program
  1. Remove any waxes or polishes from your old floor using StaticWorx EcoScrub floor stripper.
  2. Apply 2 coats of CoatZF per our instructions.
  3. Measure your floor with our ANSI/ESD S7.1 megohm meter:
    Your floor will measure <1.0 X 10 E9.
  4. Test several high-traffic areas every 2 weeks.
  5. Only clean your floor with StaticWorx ScrubWorx neutral cleaner.
Use With These StaticWorx Products

CoatZF over GroundWorx ESD epoxy

CoatZF can be applied to non-ESD floors and will give non-ESD floors static-dissipative properties. However, like any coating or wax, CoatZF wears off over time. As the coating wears off, any static-dissipative properties the non-ESD floor received from the coating will wear off as well. The only way to be sure your floor is still functioning properly/static dissipative is to test the floor regularly and after every application, using the resistance test method outlined in ANSI/ESD STM7.1.

Yes. CoatZF static-dissipative floor finish provides a low-charging walking surface and generates <100V per ANSI/ESD STM 97.2.

CoatZF has:

  • NO APE (alkylphenol ethoxylates) surfactants
  • NO Carcinogens, Mutagens, or Reproductive Toxins
  • NO Ozone-depleting compounds
  • NO Ammonia
  • NO Heavy metals (Zinc Free)
  • NO Flammable components
  • NO Components toxic to aquatic life
  • Low VOC
  • Meets CARB and other regional VOC requirements
  • Lead-free RoHS 2, REACH, and Conflict Minerals Compliant

You may also like...

Recently viewed